ACT20M-FRQ-AO-X-S
Product image
ACT20M-FRQ-AO-X-S
Connection diagram
ACT20M-FRQ-AO-X-S
Dimensioned drawing

ACT20M-FRQ-AO-X-S

Frequency signal converter, exclusive of rail bus supply, Input : Frequency, Output : 0(4)-20 mA, 0(2)-10 V

Ürün No. 2825130000
Konfigüratörde aç
Veri sayfasını indir Engineering Support Software Support Product Downloads
Aksesuarlar 2 İlgili ürünler 2
Approvals General ordering data Dimensions and weights Temperatures Environmental Product Compliance Input Output General data Insulation coordination Connection data EMC conformity and approvals Part description Classifications

Approvals

ROHS
Conform 

General ordering data

Version
Frequency signal converter, exclusive of rail bus supply, Input : Frequency, Output : 0(4)-20 mA, 0(2)-10 V 
Order No.
2825130000 
Type
ACT20M-FRQ-AO-X-S 
GTIN (EAN)
4064675360940 
Qty.
1 adet

Dimensions and weights

Depth
114,3 mm
Depth (inches)
4,5 inch
Height
112,5 mm
Height (inches)
4,429 inch
Width
6,1 mm
Width (inches)
0,24 inch
Net weight
70 g

Temperatures

Storage temperature
-40 °C...85 °C 
Operating temperature
-25 °C...70 °C 
Humidity
0...95 % (no condensation) 

Environmental Product Compliance

RoHS Compliance Status
Compliant with exemption 
RoHS Exemption (if applicable/known)
7a, 7cI 
REACH SVHC
Lead 7439-92-1 
SCIP
2f6dd957-421a-46db-a0c2-cf1609156924 

Input

Input frequency
0…100kHz 
adjustable 
Number inputs
1 
Sensor
NAMUR sensor, according to EN60947-5-6 
NPN / PNP transistor (trig-level low: ≤4 V high: ≥7 V ) 
TTL (trig-level low: ≤0.8 V high: ≥2.0 V) 
Tacho (trig-level low: ≤-50 mV high: ≥+50 mV) 
Special current (trig-level: user-defined) 
Special voltage (trig-level: user-defined) 
S0 (trig-level low: ≤2.2 mA high: ≥9.0 mA ) 
Sensor supply
5…17 V 

Output

Load impedance current
≤ 600 Ω 
load impedance voltage
≥ 10 kΩ 
Number of outputs
1 
Output behaviour on failure downscale
3,5 mA
Output behaviour on failure upscale
23 mA
Output current
0...20 mA 
4...20 mA 
in case of sensor error 
downscale (3,5 mA) 
upscale (23 mA) 
Output signal limit
<28 mA 
Output voltage, note
0(2)...10 V 
0(1)...5 V 
0(0,2)…1 V 
Type
active 
connected control must be passive 

General data

Höjdområde för drift
≤ 2000 m 
Lépés válaszideje
≤ 30 ms 
(0…90% / 100…10% of input level) 
Mounting rail
TS 35 
Nominal power consumption
0,5 VA
Power consumption, max.
1,2 W
Power consumption, typ.
0,65 W
Precisión
Basic accuracy: 0.0002 Hz 
Protection degree
IP20 
Supply voltage
24 V DC ± 30 % 
Конфигурация
DIP switch 
With FDT/DTM software 
온도 계수
≤0,01% of measurement range⁄°C 

Insulation coordination

Bemessungsspannung
300 Veff 
300 V 
EMC standards
IEC 61326-1 
Galvanic isolation
3-way isolator 
Izolační napětí
2.5 kVeff /1 min. 
Pollution severity
2 
Surge voltage category
II 

Connection data

Type of connection
Screw connection 
Tightening torque, min.
0,4 Nm
Tightening torque, max.
0,6 Nm
Clamping range, rated connection
2,5 mm²
Clamping range, min.
0,5 mm²
Clamping range, max.
2,5 mm²
Wire connection cross section AWG, min.
AWG 30 
Wire connection cross section AWG, max.
AWG 14 

EMC conformity and approvals

EMC standards
IEC 61326-1 

Part description

Product description
The universal frequency measuring transducer, which can be configured via software, disconnects and converts input signals (frequency, Namur, NPN, PNP, speedometer, TTL and S0) into an active analogue standard output signal. The power supply is galvanically isolated from the input and output (3-way isolation) by means of direct wiring. The model ACT20M-FRQ-AO-S can be supplied via the Weidmüller DIN rail bus 

Classifications

ETIM 8.0
EC002918 
ETIM 9.0
EC002918 
ETIM 10.0
EC002918 
ECLASS 14.0
27-21-01-28 
ECLASS 15.0
27-21-01-28