PRO CP 20W 24V 0.8A

PRO CP 20W 24V 0.8A

Power supply, switch-mode power supply unit, 24 V

Ürün No. 3033220000
Veri sayfasını indir Engineering Support Product Downloads
Aksesuarlar 1 İlgili ürünler 2
Approvals General ordering data Dimensions and weights Temperatures Environmental Product Compliance Input Output General data Insulation coordination Electrical safety (applied standards) Connection data (input) Connection data (output) Signalling Classifications

Approvals

Approvals
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_319222/-S800/-T1z1mm-S80) 
ROHS
Conform 

General ordering data

Version
Power supply, switch-mode power supply unit, 24 V 
Order No.
3033220000 
Type
PRO CP 20W 24V 0.8A 
GTIN (EAN)
4099986986091 
Qty.
1 adet

Dimensions and weights

Depth
29,5 mm
Depth (inches)
1,161 inch
Height
83 mm
Height (inches)
3,268 inch
Width
26,5 mm
Width (inches)
1,043 inch
Net weight
79 g

Temperatures

Storage temperature
-40 °C...90 °C 
Humidity at storage temperature
95 %, no condensation 
Operating temperature
-35 °C...50 °C 
Humidity at operating temperature
20 to 90% RH 

Environmental Product Compliance

RoHS Compliance Status
Compliant with exemption 
RoHS Exemption (if applicable/known)
7a, 7cI 
REACH SVHC
Lead 7439-92-1 
SCIP
c40c4197-e4ff-4c59-8a6f-82632592ebb9 

Input

AC input voltage range
85 … 305 V AC 
Connection system
PUSH IN with actuator 
Frequency range AC
47...63 Hz 
Input current
450 mA 
Input fuse
2 A time-lag fuse (internal) 
Inrush current
  • Input voltage:
    100 V
  • Voltage type:
    AC
  • Inrush current integral:
    0,15 A²s
  • Input voltage:
    230 V
  • Voltage type:
    AC
  • Inrush current integral:
    0,3 A²s
  • Input voltage:
    277 V
  • Voltage type:
    AC
  • Inrush current integral:
    0,35 A²s
Inrush current (typ.)
40 A
Load regulation (typ.)
2 %
Nominal power consumption
22,99 VA
Rated input voltage
100…277 V AC 
Start-up current
  • Cold start temperature:
    25 °C
  • Input voltage:
    100 V
  • Voltage type:
    AC
  • Start-up current, max.:
    20 A
  • Cold start temperature:
    25 °C
  • Input voltage:
    230 V
  • Voltage type:
    AC
  • Start-up current, max.:
    40 A
  • Cold start temperature:
    25 °C
  • Input voltage:
    277 V
  • Voltage type:
    AC
  • Start-up current, max.:
    50 A
Start-up time, max.
150 ms

Output

Capacitive load
3.000 µF 
Load Regulation (typ.)
2 %
Mains failure bridge-over time
  • Mains failure bridge-over time, min.:
    8 ms
  • Input voltage type:
    AC
  • Input voltage:
    100 V
  • Output current:
    833 mA
  • Output voltage:
    24 V
  • Mains failure bridge-over time, min.:
    30 ms
  • Input voltage type:
    AC
  • Input voltage:
    230 V
  • Output current:
    833 mA
  • Output voltage:
    24 V
  • Mains failure bridge-over time, min.:
    50 ms
  • Input voltage type:
    AC
  • Input voltage:
    277 V
  • Output current:
    833 mA
  • Output voltage:
    24 V
Max. residual ripple
240 mVss 
Output power
20 W
Output voltage, max.
24,72 V
Output voltage, min.
23,28 V
Overload protection
120 … 180 %, switch off mode 
Rated output voltage
24 V DC ± 3 % 
Výstupní proud, max.
833 mA

General data

Building height
83 mm
Building Width
26,5 mm
Degree of efficiency (typ.)
87 %
Mounting position, installation notice
Horizontal on DIN rail TS 35, top and bottom 50 mm clearance for free air flow, 10 mm clearance to neighbouring subassemblies. 
On TS 35 mounting rail, 50 mm clearance above and below for free air supply. 
MTBF
  • According to Standard:
    MLT-HDBK-217F
  • Operating time (hours), min.:
    1.000.000 h
  • Ambient temperature:
    25 °C
  • Input voltage:
    230 V
  • Output power:
    20 W
  • Duty cycle:
    100 %
Power loss, idling
100 mW
Protection degree
IP30 
Short-circuit protection
Yes 
Standards
EN 60335-1 
Surge voltage category
III 

Insulation coordination

Humidity at storage temperature
95 %, no condensation 
Insulation voltage, input/output
4 kV
Protection class
II 
Surge voltage category
III 

Electrical safety (applied standards)

Safety transformers for switch-mode power supplies
According to EN 61558-2-16 
Tensión baja de protección
SELV according to EN 62368-1 

Connection data (input)

Conductor cross-section, AWG/kcmil , max.
12 AWG
Conductor cross-section, AWG/kcmil , min.
26 AWG
Conductor cross-section, flexible , min.
0,2 mm²
Conductor cross-section, rigid , max.
2,5 mm²
Conductor cross-section, rigid , min.
0,2 mm²
Connection system
PUSH IN with actuator 
Number of terminals
2 (L,N) 
Stripping length (input)
10 mm
Wire connection cross section, flexible (input), max.
2,5 mm²

Connection data (output)

Conductor cross-section, AWG/kcmil , min.
28 AWG
Conductor cross-section, rigid , max.
1,5 mm²
Conductor cross-section, rigid , min.
0,2 mm²
Kapcsok száma
2 (+ / -) 
Ledardiameter, flexibel , min.
0,14 mm²
Stripping length (output)
10 mm
Сечение подключаемого провода, гибкого , макс.
1,5 mm²
컨덕터 단면적, AWG/kcmil , 최대
14 AWG

Signalling

LED green
Operating voltage OK 

Classifications

ETIM 8.0
EC002540 
ETIM 9.0
EC002540 
ETIM 10.0
EC002540 
ECLASS 14.0
27-04-07-01 
ECLASS 15.0
27-04-07-01