ACT20C-AI-AO-MTCP
Product image
.
ACT20C-AI-AO-MTCP
ACT20C-AI-AO-MTCP
Connection diagram
ACT20C-AI-AO-MTCP
ACT20C-AI-AO-MTCP
ACT20C-AI-AO-MTCP
ACT20C-AI-AO-MTCP
ACT20C-AI-AO-MTCP
ACT20C-AI-AO-MTCP
ACT20C-AI-AO-MTCP

ACT20C-AI-AO-MTCP

Produkt ID 1334490000
Download datablad Engineering Support Software Support Product Downloads
Tilbehør 3 Anvendte produkter 8
Approvals General ordering data Dimensions and weights Temperatures Environmental Product Compliance Input Interface 1 Output Output (analogue) General data Insulation coordination Connection data Important note Classifications

Approvals

Approvals
DNVGL;  
ROHS
Conform  

General ordering data

Order No.
1334490000  
Type
ACT20C-AI-AO-MTCP  
GTIN (EAN)
4050118137675  
Qty.
1  Styk
Delivery status
This article will no longer be available in the future.  
Available until
31.05.2023  

Dimensions and weights

Depth
113,6  mm
Depth (inches)
4,472  inch
Width
22,5  mm
Width (inches)
0,886  inch
Length
119,2  mm
Length (inches)
4,693  inch
Net weight
169  g

Temperatures

Storage temperature
-20 °C...85 °C  
Operating temperature
-20 °C...70 °C  
Humidity
0...95 % (no condensation)  

Environmental Product Compliance

RoHS Compliance Status
Compliant with exemption  
RoHS Exemption (if applicable/known)
7a, 7cI  
REACH SVHC
Lead 7439-92-1  
SCIP
2f6dd957-421a-46db-a0c2-cf1609156924  

Input

Input current
0...20 mA  
4...20 mA  
Input voltage
0(2)…10 V  
Number of inputs
1  
Sensor supply
> 17 V DC at 20 mA  

Interface 1

Addressing
DHCP or manual adjustment  
Interface
RJ45: female-female, Cat.5 to 100 MHz  
Jack plug for CBX200  
Protocol
FDT/DTM  
Modbus/TCP  

Output

Load impedance current
≤ 500 Ω  
load impedance voltage
≥ 10 kΩ  
Number of outputs
1  
Output current
0...20 mA  
4...20 mA  
Output voltage, note
0...10 V  

Output (analogue)

Load resistance current
≤ 500 Ω  
Load resistance voltage
≥ 10 kΩ  
Output current
0(4)...20 mA  
Output voltage
0...10 V  
Transmit function
direct or inverted  

General data

Accuracy
< 0.15% end value (+ 0.05% > 55 °C)  
Current: 1 uA / 30 uA (+ 10 uA > 55°C)  
Voltage: 1 mV / 15 mV (+ 5 mV > 55°C)  
Configuration
FDT/DTM (Ethernet or service interface)  
Power consumption
≤ 3.5 W  
Protection degree
IP20  
Rail
TS 35  
Temperature coefficient
≤ 0.01 % / °C  
Voltage supply
24 V DC ± 25 %  

Insulation coordination

EMC standards
EN 61326-1:2006  
Galvanic isolation
4-way isolator;  
between input / output / power supply / Ethernet  
Pollution severity
2  
Rated voltage ⁄ test voltage: Ethernet interface to supply ⁄ functional earth to supply ⁄ Ethernet interface
31.2 V DC / 0.9 kV rmsin secondary electrical circuits, basic insulation  
Rated voltage ⁄ test voltage: functional earth to input ⁄ output
300 Vrms / 1.1 kV rms in secondary electrical circuits, basic insulation  
Rated voltage ⁄ test voltage: input/output to output/input ⁄ supply⁄ Ethernet interface
300 Vrms / 1.7 kV rmsin secondary electrical circuits, reinforced insulation  
Recommendations
Namur NE43  
Namur NE44  
Namur NE107  

Connection data

Type of connection
Screw connection/ RJ45 plug-in connector  
Tightening torque, min.
0,4  Nm
Tightening torque, max.
0,6  Nm
Clamping range, rated connection
1,5  mm²
Clamping range, min.
0,5  mm²
Clamping range, max.
2,5  mm²
Wire connection cross section AWG, min.
AWG 30  
Wire connection cross section AWG, max.
AWG 14  
Wire cross-section, solid, min.
0,5  mm²
Wire cross-section, solid, max.
2,5  mm²

Important note

Product information

With the ACT20C, Weidmüller is presenting a completely new type of signal converter. The compact module is equipped with an Ethernet connection and provides, in addition to signals, precise information on the status of sensors, signal processing and cabling.

ACT20C, as a signal converter, isolates, scales and converts analogue current and voltage signals; it can be configured directly with the "WI-Manager" software or via an Ethernet network.
The software is based on the supplier-independent FDT/DTM technology.

The ACT20C has been designed specifically for process automation in order to continuously forward measured values and status information to networked devices. During standard operation,
malfunction, maintenance or configuration via the network, this allows a precise display of the current status.
In case of error, the ACT20C supplies precise information for error analysis and can therefore contribute to higher system availability.

 

Classifications

ETIM 6.0
EC002653  
ETIM 7.0
EC002653  
ETIM 8.0
EC002653  
ETIM 9.0
EC002653  
ETIM 10.0
EC002653  
ECLASS 9.0
27-21-01-20  
ECLASS 9.1
27-21-01-90  
ECLASS 10.0
27-21-01-20  
ECLASS 11.0
27-21-01-20  
ECLASS 12.0
27-21-01-20  
ECLASS 13.0
27-21-01-20  
ECLASS 14.0
27-21-01-20  
ECLASS 15.0
27-21-01-20