ACT20M-FRQ-AO-X-S
Product image
ACT20M-FRQ-AO-X-S
Connection diagram
ACT20M-FRQ-AO-X-S
Dimensioned drawing
ACT20M-FRQ-AO-X-S

ACT20M-FRQ-AO-X-S

Frequency signal converter, exclusive of rail bus supply, Input : Frequency, Output : 0(4)-20 mA, 0(2)-10 V

Produkt ID 2825130000
Åbn i konfiguratoren
Download datablad Engineering-support Software-support Produktdownloads
Tilbehør 2 Anvendte produkter 2
Approvals General ordering data Dimensions and weights Temperatures Environmental Product Compliance Entrée 출력 General data Coordenadas de aislamiento Connection data EMC conformity and approvals Part description Classifications

Approvals

ROHS
Conform 

General ordering data

Version
Frequency signal converter, exclusive of rail bus supply, Input : Frequency, Output : 0(4)-20 mA, 0(2)-10 V 
Order No.
2825130000 
Type
ACT20M-FRQ-AO-X-S 
GTIN (EAN)
4064675360940 
Qty.
1 Styk

Dimensions and weights

Depth
114,3 mm
Depth (inches)
4,5 inch
Height
112,5 mm
Height (inches)
4,429 inch
Width
6,1 mm
Width (inches)
0,24 inch
Net weight
70 g

Temperatures

Storage temperature
-40 °C...85 °C 
Operating temperature
-25 °C...70 °C 
Humidity
0...95 % (no condensation) 

Environmental Product Compliance

RoHS Compliance Status
Compliant with exemption 
RoHS Exemption (if applicable/known)
7a, 7cI 
REACH SVHC
Lead 7439-92-1 
SCIP
2f6dd957-421a-46db-a0c2-cf1609156924 

Entrée

Input frequency
0…100kHz 
regolabile 
Number inputs
1 
Sensor
NAMUR sensor, according to EN60947-5-6 
NPN / PNP transistor (trig-level low: ≤4 V high: ≥7 V ) 
TTL (trig-level low: ≤0.8 V high: ≥2.0 V) 
Tacho (trig-level low: ≤-50 mV high: ≥+50 mV) 
Special current (trig-level: user-defined) 
Special voltage (trig-level: user-defined) 
S0 (trig-level low: ≤2.2 mA high: ≥9.0 mA ) 
Sensor supply
5…17 V 

출력

Load impedance current
≤ 600 Ω 
load impedance voltage
≥ 10 кОм 
Number of outputs
1 
Output behaviour on failure downscale
3,5 mA
Output behaviour on failure upscale
23 mA
Output current
0...20 mA 
4...20 mA 
in case of sensor error 
downscale (3,5 mA) 
upscale (23 mA) 
Output signal limit
<28 mA 
Output voltage, note
0(2)...10 V 
0(1)...5 V 
0(0,2)…1 V 
Type
active 
connected control must be passive 

General data

Accuracy
Basic accuracy: 0.0002 Hz 
Configuration
DIP switch 
With FDT/DTM software 
Mounting rail
TS 35 
Nominal power consumption
0,5 VA
Operating altitude
≤ 2000 m 
Protection degree
IP20 
Spotřeba elektrické energie, max.
1,2 W
Spotřeba elektrické energie, typ.
0,65 W
Step response time
≤ 30 ms 
(0…90% / 100…10% of input level) 
Supply voltage
24 V DC ± 30 % 
Temperature coefficient
≤0,01% of measurement range⁄°C 

Coordenadas de aislamiento

EMC standards
IEC 61326-1 
Galvanic isolation
Triple isolateur 
Insulation voltage
2.5 kVeff / 1 분 
Pollution severity
2 
Rated voltage
300 Veff 
300 V 
Surge voltage category
II 

Connection data

Type of connection
Screw connection 
Tightening torque, min.
0,4 Nm
Tightening torque, max.
0,6 Nm
Clamping range, rated connection
2,5 mm²
Clamping range, min.
0,5 mm²
Clamping range, max.
2,5 mm²
Wire connection cross section AWG, min.
AWG 30 
Wire connection cross section AWG, max.
AWG 14 

EMC conformity and approvals

EMC standards
IEC 61326-1 

Part description

Produktbeschreibung
The universal frequency measuring transducer, which can be configured via software, disconnects and converts input signals (frequency, Namur, NPN, PNP, speedometer, TTL and S0) into an active analogue standard output signal. The power supply is galvanically isolated from the input and output (3-way isolation) by means of direct wiring. The model ACT20M-FRQ-AO-S can be supplied via the Weidmüller DIN rail bus 

Classifications

ETIM 8.0
EC002918 
ETIM 9.0
EC002918 
ETIM 10.0
EC002918 
ECLASS 14.0
27-21-01-28 
ECLASS 15.0
27-21-01-28