ACT20M-TCI-AO-S
Product image
ACT20M-TCI-AO-S
Connection diagram
ACT20M-TCI-AO-S
Dimensional drawing
ACT20M-TCI-AO-S
ACT20M-TCI-AO-S
ACT20M-TCI-AO-S

ACT20M-TCI-AO-S

Temperature converter, Thermocouple, With galvanic isolation, Input : Temperature, thermocouple, Output : I / U

Tuotteen tunnus 1375480000
Lataa tietosivu Engineering Support Software Support Product Downloads
Lisävarusteet 4 Samankaltaiset tuotteet 13
General ordering data Dimensions and weights Temperatures Probability of failure Environmental Product Compliance Input Output General data Insulation coordination Data for Ex applications (ATEX) Connection data EMC conformity and approvals Important note Classifications Approvals

General ordering data

Version
Temperature converter, Thermocouple, With galvanic isolation, Input : Temperature, thermocouple, Output : I / U  
Order No.
1375480000  
Type
ACT20M-TCI-AO-S  
GTIN (EAN)
4050118259650  
Qty.
1  items

Dimensions and weights

Depth
114,3  mm
Depth (inches)
4,5  inch
Height
112,5  mm
Height (inches)
4,429  inch
Width
6,1  mm
Width (inches)
0,24  inch
Net weight
84  g

Temperatures

Storage temperature
-40 °C...85 °C  
Operating temperature
-25 °C...70 °C  
Humidity at operating temperature
0...95 % (no condensation)  
Humidity
40 °C / 93 % rel. humidity, no condensation  

Probability of failure

MTBF
147  a

Environmental Product Compliance

RoHS Compliance Status
Compliant with exemption  
RoHS Exemption (if applicable/known)
7a, 7cI  
REACH SVHC
Lead 7439-92-1  
SCIP
2f6dd957-421a-46db-a0c2-cf1609156924  

Input

Number of inputs
1  
Sensor
Thermocouples: J, K  
Temperature input range
Configurable  
J: (-100…+1200 °C)  
K: (-180…+1372 °C)  
min. measurement range 50°C (TC)  

Output

Load impedance current
≤ 600 Ω  
load impedance voltage
≥ 10 kΩ  
Number of outputs
1  
Output current
configurable  
0...20 mA  
4...20 mA  
Output voltage, note
configurable  
0(2)...10 V  
0(1)...5 V  
Type
active  
connected control must be passive  
Wire break detection
Yes  
Configurable  
3.5 mA / 23 mA / none  

General data

Accuracy
absolute accuracy: <±0.05 % of the measurement range  
Basic accuracy: <±0.5°  
Configuration
DIP switch  
Delivery state
  • Setting parameters:
    Input
  • Configuration:
    0 °C
  • Setting parameters:
    Bandwidth
  • Configuration:
    50 Hz
  • Setting parameters:
    Output 1
  • Configuration:
    0...20 mA
  • Setting parameters:
    Output 2
  • Configuration:
    0...20 mA
  • Setting parameters:
    Sensor error detection
  • Configuration:
    enabled
  • Setting parameters:
    Step response time
  • Configuration:
    < 30 ms
  • Setting parameters:
    Noise suppression
  • Configuration:
    enabled
Delivery state
Input: 0 °C // Bandwidth: 50 Hz // Output 1: 0...20 mA // Output 2: 0...20 mA // Sensor error detection: enabled // Step response time: < 30 ms // Noise suppression: enabled  
Galvanic isolation
3-way isolator  
Nominal power consumption
0,5  VA
Power consumption, max.
0,7  W
Power consumption, typ.
0,49  W
Protection degree
IP20  
Rail
TS 35  
Step response time
Configurable  
≤ 30 ms  
<300 ms  
Temperature coefficient
0,1 °C ⁄ °C  
or  
≤0,01% des Messbereichs⁄°C  
Voltage supply
24 V DC ±30 % at terminal or via CH20M rail bus  

Insulation coordination

EMC standards
IEC 61326-1  
Galvanic isolation
3-way isolator  
Insulation voltage
2.5 kVeff /1 min.  
Pollution severity
2  
Rated voltage
300 Veff  
Surge voltage category
II  

Data for Ex applications (ATEX)

Installation location
Device installed in safe area, zone 2  
Marking
II 3 G Ex nA IIC T4 Gc  

Connection data

Type of connection
Screw connection  
Tightening torque, min.
0,4  Nm
Tightening torque, max.
0,6  Nm
Clamping range, rated connection
2,5  mm²
Clamping range, min.
0,5  mm²
Clamping range, max.
2,5  mm²
Wire connection cross section AWG, min.
AWG 30  
Wire connection cross section AWG, max.
AWG 14  

EMC conformity and approvals

EMC standards
IEC 61326-1  
Standards
IEC 61010-1  

Important note

Product information
The ACT20M-TCI-AO-S configurable temperature transducer isolates and converts analogue signals. An analogue thermocouple input signal (Type J, K) is linearly converted into an analogue output signal and is galvanically isolated. The power supply is galvanically isolated from the input and output (3-way isolation) and this is done with direct wiring or over the Weidmüller rail bus.  

Classifications

ETIM 6.0
EC002919  
ETIM 7.0
EC002919  
ETIM 8.0
EC002919  
ETIM 9.0
EC002919  
ETIM 10.0
EC002919  
ECLASS 9.0
27-21-01-29  
ECLASS 9.1
27-21-01-29  
ECLASS 10.0
27-21-01-29  
ECLASS 11.0
27-21-01-29  
ECLASS 12.0
27-21-01-29  
ECLASS 13.0
27-21-01-29  
ECLASS 14.0
27-21-01-29  
ECLASS 15.0
27-21-01-29  

Approvals

Approvals
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_319228/-S800/-T1z1mm-S80)  
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_319234/-S800/-T1z1mm-S80)  
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_319237/-S800/-T1z1mm-S80)  
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_319240/-S800/-T1z1mm-S80)  
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_319243/-S800/-T1z1mm-S80)  
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_319260/-S800/-T1z1mm-S80)  
ROHS
Conform  
UL File Number Search
[UL Website](https://database.ul.com/cgi-bin/XYV/cgifind/LISEXT/1FRAME/gfilenbr.html)  
Certificate no. (cULus)
E337701