text.skipToContent text.skipToNavigation

Lataa tietosivu Samankaltaiset tuotteet

ACT20P BRIDGE

Measuring bridge converter, Input : Resistance measuring bridge, Output : 0(4)-20 mA, 0-10 V

Tuotteen tunnus 1067250000

Ominaisuudet

General ordering data

Version	Measuring bridge converter, Input : Resistance measuring bridge, Output : 0(4)-20 mA, 0-10 V
Order No.	1067250000
Type	ACT20P BRIDGE
GTIN (EAN)	4032248820856
Qty.	1 items

Dimensions and weights

Depth	113,6 mm
Depth (inches)	4,472 inch
Height	119,2 mm
Height (inches)	4,693 inch
Width	22,5 mm
Width (inches)	0,886 inch
Net weight	198 g

Temperatures

Storage temperature	-40 °C...85 °C
Operating temperature	-40 °C...70 °C
Humidity	10…90 %, no condensation

Probability of failure

SIL in compliance with IEC 61508	None
MTTF	543 a

Environmental Product Compliance

RoHS Compliance Status	Compliant with exemption
RoHS Exemption (if applicable/known)	7a, 7cI
REACH SVHC	Lead 7439-92-1
SCIP	2f6dd957-421a-46db-a0c2-cf1609156924

Input

Bridge sensitivity	1.0 mV / V to 5.0 mV / V
Bridge supply voltage	5 V or 10 V
Input signal	±10 mV / ±20 mV / ±30 mV / ±50 mV
Number of inputs	1
Sensor	Strain gauge resistance Resistance measurement Total resistance of all parallel resistance measuring bridges: min. 87 Ω
Sensor supply	120 mA @ 10 V (= 4 x 350 Ω bridge resistors)

Output

Load impedance current	≤ 600 Ω
load impedance voltage	600 Ω
Output current	0…22 mA (adjustable)
Output voltage, note	0…11 V (adjustable)
Type	active connected control must be passive

Output (digital)

Max. switching voltage, AC	0 V
Rated switching current	0.1 A

General data

Accuracy	<0.05 % of measuring range
Configuration	DIP switch and button
Linearity	Typically ± 0.05 % of signal range
Long-term drift	0.1 % / 10.000 h
Power consumption	3 W @ 24 V DC
Protection degree	IP20
Rail	TS 35
Step response time	<400 ms (10…90 %)
Temperature coefficient	typ. 0.005 % / °C
Voltage supply	10…60 V DC

Insulation coordination

EMC standards	EN 61326
Insulation voltage	5.7 kV (input / output, input / supply)
Pollution severity	2
Rated voltage	300 V
Surge voltage category	III

Connection data

Type of connection	Screw connection
Tightening torque, min.	0,4 Nm
Tightening torque, max.	0,6 Nm
Clamping range, rated connection	2,5 mm²
Clamping range, min.	0,5 mm²
Clamping range, max.	2,5 mm²
Wire connection cross section AWG, min.	AWG 26
Wire connection cross section AWG, max.	AWG 12

Important note

Product information

The ACT20P-BRIDGE-S bridge measuring transducer converts measuring bridge voltages into standard signals. Buttons are used for adjustment to the measuring bridge connected. The bridge measuring transducer can supply up to 4 parallel-connected measuring bridges each with 350 Ω. The device supports simple compensation of the tare weight with a separate input for an external button or an external PLC signal. The power supply is electrogalvanised and isolated from the input and output (3-way isolation).

Properties

4-wire and 6-wire measurement
Supply of up to 4 parallel-connected measuring bridges each with 350 Ω
Input and output ranges can be adjusted via DIP switches
Tara compensation via external button or PLC signal
Operating status display on a front panel LED
Galvanic 3-way isolation between input, output and supply.

Downloads

Approval/Certificate/Document of Conformity	[Declaration of Conformity](https://mdcop.weidmueller.com/mediadelivery/asset/900_37673)
Engineering Data	[CAD data -- STEP](https://mdcop.weidmueller.com/mediadelivery/asset/900_53606)
Eplan Data Portal	[Eplan data](https://dataportal.eplan.com/part-details/WEI.1067250000)
CADENAS eCATALOG	[CAX data](https://weidmueller-embedded.partcommunity.com?catalog=weidmueller_qs&part=1067250000)
Software	[DIP switch configuration tool](https://mdcop.weidmueller.com/mediadelivery/asset/900_35389)
User Documentation	[Quickstart guide german](https://mdcop.weidmueller.com/mediadelivery/asset/900_37769) [Device description -- Instruction sheet](https://mdcop.weidmueller.com/mediadelivery/asset/900_40084) [Quickstart guide english](https://mdcop.weidmueller.com/mediadelivery/asset/900_237166)
Catalogues	[Catalogues in PDF-format](LINK/Catalog.html)

Classifications

ETIM 6.0	EC002653
ETIM 7.0	EC002653
ETIM 8.0	EC002653
ETIM 9.0	EC002653
ECLASS 9.0	27-21-01-20
ECLASS 9.1	27-21-01-20
ECLASS 10.0	27-21-01-20
ECLASS 11.0	27-21-01-20
ECLASS 12.0	27-21-01-20
ECLASS 13.0	27-21-01-20
ECLASS 14.0	27-21-01-20

Tender specification sheets

Long specification

Bridge measuring transformer with electrical 3-way isolation, configurable
measurement isolating transformer in 22.5 mm width with external power supply, for recording,
transforming and isolating of measurements from industrial strain gauges.
Standard DC current/voltage signals are available on the output side. Measuring bridges of up to
3 x 350 Ohm can be supplied via the input circuit. Automatic tare calibration
via external switch signal, or manually with a press of a button.
6-wire connection compensates for differences in wire resistance. Bridge excitation voltage
can be switched between 5 v and 10 V. Load cells can be calibrated using a button on the front side.
I/O signals can be configured via DIP switches.

Add-on housing for TS35 rail mounting
Dimensions: L/W/H 119.2/ 22.5/ 113.6 mm
Screw connection / Nominal cross-section 2.5 mm²Protection degree: IP 20

Input                          Resistance measuring bridge / 1 mV / V... 5 mV / V
Bridge sensitivity +/- 10 mV / +/- 20 mV / +/- 30 mV / +/- 50 mV (adjustable)
Input resistance > 1 MOhm
Bridge supply 5 V or 10 V
Output                                              0...11 V / 0...22 mA configurable
Load resistance             < 600 Ohm/ Strom/> 1 kOhm/ voltage
Temperature coefficient typ. 50 ppm / K
Transmission error               typ. 0.05 % of input
Step response time         < 400 ms (10...90 %)
Auxiliary power                                     10...60 VDC
Ambient
temperature range -40°C...+70 °C

Isolation                                 EN 50178, 3-way isolation up to 5.7 kV of all circuits against each other
Test voltage                               4 kV input against output against auxiliary power
Rated
voltage                                          300 V AC/DC at overvoltage category III and pollution degree 2
Approvals cULus

Type ACT20P-BRIDGE-S

Short specification

Approvals

Approvals	![CE](/picture/CE.gif)
Approvals	CULUS;
ROHS	Conform

Lisävarusteet

MarkersDevice markersMultiCardESGESG 8/13.5/43.3 SAI AUBlank

ESG 8/13.5/43.3 SAI AU 5C

Tuotteen tunnus:

1912130000

VPE:

5 items

ESG, Device markers x 13.5 mm, PA 66, Colour: Transparent

Tuotesivu Lataukset

MarkersDevice markersMultiCardESGESG 6.6/... BHZBlank

ESG 6.6/20 BHZ 5.00/04 5C

Tuotteen tunnus:

1082540000

VPE:

200 items

ESG, Device markers x 20 mm, PA 66, Colour: white

Tuotesivu Lataukset

Yksittäiset osat

Electronics HousingsModular electronics housingsConnection system - CH20MPCB connectors four pole - CH20M22, CH20M45, CH20M67Female plugs - Clamping yoke screw connection

BHZ 5.00/04/90LH BK/BK

Tuotteen tunnus:

1069350000

VPE:

78 items

PCB plug-in connector Black release lever cod. 02

Tuotesivu Lataukset

Connectivity

Electronics

Automation & Software

Workplace & Accessories

Assembly

ACT20P BRIDGE

Ominaisuudet

Lisävarusteet

ESG 8/13.5/43.3 SAI AU 5C

ESG 6.6/20 BHZ 5.00/04 5C

Yksittäiset osat

BHZ 5.00/04/90LH BK/BK

Suositut kategoriat

Kiinnostavia linkkejä

Ratkaisut

Connectivity

Electronics

Automation & Software

Workplace & Accessories

Assembly

ACT20P BRIDGE

Ominaisuudet

Lisävarusteet

ESG 8/13.5/43.3 SAI AU 5C

ESG 6.6/20 BHZ 5.00/04 5C

Yksittäiset osat

BHZ 5.00/04/90LH BK/BK