ACT20P-CI-2CO-P-S
Similar to illustration
ACT20P-CI-2CO-P-S
ACT20P-CI-2CO-P-S
Dimensioned drawing
ACT20P-CI-2CO-P-S
Similar to illustration
ACT20P-CI-2CO-P-S

ACT20P-CI-2CO-P-S

Analogue isolating amplifier, Input : 0(4)-20 mA, Output : 2 x 0(4) - 20 mA, Voltage supply also via CH20M rail bus, HART®

Tuotteen tunnus 1506220000
Lataa tietosivu Engineering Support Product Downloads
Lisävarusteet 2 Yksittäiset osat 1 Samankaltaiset tuotteet 6
General ordering data Dimensions and weights Temperatures Probability of failure Environmental Product Compliance Input Output Output (digital) General data Insulation coordination Data for Ex applications (ATEX) Connection data Important note Classifications Approvals

General ordering data

Version
Analogue isolating amplifier, Input : 0(4)-20 mA, Output : 2 x 0(4) - 20 mA, Voltage supply also via CH20M rail bus, HART®  
Order No.
1506220000  
Type
ACT20P-CI-2CO-P-S  
GTIN (EAN)
4050118314724  
Qty.
1  items

Dimensions and weights

Depth
113,7  mm
Depth (inches)
4,476  inch
Height
127,1  mm
Height (inches)
5,004  inch
Width
12,5  mm
Width (inches)
0,492  inch
Net weight
160  g

Temperatures

Storage temperature
-40 °C...85 °C  
Operating temperature
-20 °C...60 °C  
Humidity at operating temperature
0...95 % (no condensation)  
Humidity
5...95 %, no condensation  

Probability of failure

SIL in compliance with IEC 61508
None  

Environmental Product Compliance

RoHS Compliance Status
Compliant with exemption  
RoHS Exemption (if applicable/known)
7a, 7cI  
REACH SVHC
Lead 7439-92-1  
SCIP
2f6dd957-421a-46db-a0c2-cf1609156924  

Input

Input current
0...20 mA  
4…20mA  
Input signal
HART signal® bidirectional  
Number of inputs
1  
Sensor
2-wire transmitter (without own power supply)  
3-wire sensor  
4- wire sensor (with own power supply)  
Sensor supply
> 17 V DC at 20 mA  
Voltage drop
ca. 3.8 V @ RLoad = 0 Ω; ca. 15 V @ RLoad = 600 Ω; (Iinput = 20 mA)  

Output

Load impedance current
<300 Ω  
Number of outputs
2  
Output current
0…20 mA (if input: 0…20 mA)  
4…20 mA (if input: 4…20 mA)  
HART® digital signal  
Type
active  
connected control must be passive  

Output (digital)

Max. switching voltage, AC
0  V
Max. switching voltage, DC
0  V
Rated switching current
0.1 A  

General data

Accuracy
<0.1 % of end value  
Configuration
none  
Current consumption
≤60 mA (24V power supply, 20mA output)  
Galvanic isolation
3-way isolator  
between input ⁄ output ⁄ supply  
Nominal power consumption
2  VA
Operating altitude
≤ 2000 m  
Protection degree
IP20  
Rail
TS 35  
Step response time
≤ 0,5 ms  
Temperature coefficient
80 ppm/K  
Type of signal forwarding according to HART®
unchanged  
Voltage supply
20…30 V DC  

Insulation coordination

EMC standards
EN 61326-1  
EN 61000-6-2  
EN 61000-6-4  
Galvanic isolation
3-way isolator  
between input ⁄ output ⁄ supply  
Impulse withstand voltage
4 kV (1.2/50 µs)  
Insulation voltage
2 kV inputs / outputs / power supply  
Insulation voltage input or output/supply
2 kV inputs / outputs / power supply  
Pollution severity
2  
Surge voltage category
III  
Test voltage
0,3  kV

Data for Ex applications (ATEX)

Marking
II 3 G Ex ec IIC T5 Gc  

Connection data

Type of connection
Screw connection  
Tightening torque, min.
0,4  Nm
Tightening torque, max.
0,6  Nm
Clamping range, rated connection
2,5  mm²
Clamping range, min.
0,5  mm²
Clamping range, max.
2,5  mm²
Wire connection cross section AWG, min.
AWG 26  
Wire connection cross section AWG, max.
AWG 12  

Important note

Product information
The non-adjustable DC isolating amplifier ACT20P-CI-2CO isolates analogue standard current signals from a power source or from a 2- or 3-wire sensor. An analogue input current signal is converted linearly and doubled to provide two galvanically isolated output current signals. The power supply is galvanically isolated from the input and output (4-way isolation).

Properties
  • HART-compatible for 0.5 - 2.5 kHz
  • The active or passive mA signal inputs are fully galvanically isolated.
  • Operating status display on a front panel LED
  • Galvanic 4-way isolation between input, output and supply.
 

Classifications

ETIM 6.0
EC002653  
ETIM 7.0
EC002653  
ETIM 8.0
EC002653  
ETIM 9.0
EC002653  
ETIM 10.0
EC002653  
ECLASS 9.0
27-21-01-20  
ECLASS 9.1
27-21-01-20  
ECLASS 10.0
27-21-01-20  
ECLASS 11.0
27-21-01-20  
ECLASS 12.0
27-21-01-20  
ECLASS 13.0
27-21-01-20  
ECLASS 14.0
27-21-01-20  
ECLASS 15.0
27-21-01-20  

Approvals

Approvals
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_319222/-S800/-T1z1mm-S80)  
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_319228/-S800/-T1z1mm-S80)  
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_322323/-S800/-T1z1mm-S80)  
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_319213/-S800/-T1z1mm-S80)  
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_319240/-S800/-T1z1mm-S80)  
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_319260/-S800/-T1z1mm-S80)  
ROHS
Conform  
UL File Number Search
[UL Website](https://database.ul.com/cgi-bin/XYV/cgifind/LISEXT/1FRAME/gfilenbr.html)  
Certificate no. (cULus)
E366074  
Certificate no. (cULusEX)
E338066