WAS2 VMR 3PH
WAS2 VMR 3PH
Connection diagram
WAS2 VMR 3PH
WAS2 VMR 3PH

WAS2 VMR 3PH

WAVESERIES, Voltage monitoring, 1 x three-phase (R, S, T, N), 250 V, Screw connection

Produkt ID 8705630000
Download datablad Product Downloads Engineering Support
Tilbehør 1 Anvendte produkter 3
General ordering data Dimensions and weights Temperatures Probability of failure Environmental Product Compliance Input Output (digital) General data Insulation coordination Connection data Important note Classifications Tender specification sheets Approvals

General ordering data

Version
WAVESERIES, Voltage monitoring, 1 x three-phase (R, S, T, N), 250 V, Screw connection  
Order No.
8705630000  
Type
WAS2 VMR 3PH  
GTIN (EAN)
4032248377060  
Qty.
1  Styk
Delivery status
This article will no longer be available in the future.  
Available until
31.12.2022  
Alternative product
[7760054165](~/p/7760054165)  

Dimensions and weights

Depth
112,4  mm
Depth (inches)
4,425  inch
Width
22,5  mm
Width (inches)
0,886  inch
Length
96,5  mm
Length (inches)
3,799  inch
Net weight
120,6  g

Temperatures

Storage temperature
-25 °C...85 °C  
Operating temperature
0 °C...70 °C  
Humidity at operating temperature
0...95 % (no condensation)  

Probability of failure

SIL in compliance with IEC 61508
None  
MTTF
493  a

Environmental Product Compliance

RoHS Compliance Status
Compliant with exemption  
RoHS Exemption (if applicable/known)
7a, 7cI  
REACH SVHC
Lead 7439-92-1  
SCIP
b25f3b7c-b874-4a4e-a8b2-4f423a7e2a65  

Input

Input frequency
50...60Hz  
Input voltage
80…250 V AC/DC 3~  
200...400 V AC/DC  
Number of inputs
1 x three-phase (R, S, T, N)  

Output (digital)

Alarm function
configurable  
Surge voltage  
Undervoltage  
Hysteresis: 10 V  
Continuous current
3 A  
Max. switching voltage, AC
0  V
Rated switching current
0.1 A  
Type
2 CO contacts  

General data

Configuration
DIP switch and potentiometer  
Alarm status reset via reset input or button  
Nominal power consumption
1,5  VA
Protection degree
IP20  
Rail
TS 35  
Repeat accuracy
<0.3 % of set range  
Step response time
<300 ms  
Temperature coefficient
≤ 300 ppm/K  
Voltage supply
from the measuring circuit  

Insulation coordination

EMC standards
EN 61000-6-1, 2, 3, 4  
Galvanic isolation
3-way isolator  
Impulse withstand voltage
6 kV  
Insulation voltage
4 kVeff / 1 min.  
Pollution severity
2  
Rated voltage
600 V  
Surge voltage category
III  

Connection data

Type of connection
Screw connection  
Clamping range, rated connection
2,5  mm²
Clamping range, min.
0,5  mm²
Clamping range, max.
2,5  mm²

Important note

Product information
This product will soon be replaced by a new product.
Please do not use with new systems. Please contact our technical support.  

Classifications

ETIM 6.0
EC002653  
ETIM 7.0
EC002653  
ETIM 8.0
EC002653  
ETIM 9.0
EC002653  
ETIM 10.0
EC002653  
ECLASS 9.0
27-21-01-20  
ECLASS 9.1
27-21-01-20  
ECLASS 10.0
27-21-01-20  
ECLASS 11.0
27-21-01-20  
ECLASS 12.0
27-21-01-20  
ECLASS 13.0
27-21-01-20  
ECLASS 14.0
27-21-01-20  
ECLASS 15.0
27-21-01-20  

Tender specification sheets

Long specification

Limit-value monitoring component   for 1- /3- phase AC and DC voltages
with relay output and electrical isolation
limit-value monitoring component in 22.5 mm width for recording 1-phase
AC/DC voltages 200...400 V or 3-phase AC- voltages of 80...250 V.
A relay contact (CO) with a switching capacity of 750 VA
is available on the output side.
Input ranges, high/low trip alarm, monitored voltage window and
switching behaviour (for working and quiescent currents) can be configured using DIP switches
Switching threshold can be adjusted with front-side potentiometer
Power is supplied via the measured circuit. The I/O circuits have 6 kV of electrical isolation.


Add-on housing for TS35 rail mounting
Dimensions: L/W/H 96.5/ 17.5/ 112.4 mm
Screw connection / Nominal cross-section 2.5 mm2
Protection degree: IP 20  

Input                         3 phases 80 V...250 V AC
                                      1 phase 200...400 V AC/DC
                                      switchable
Voltage of measuring circuit max 400 V
Output                                             Relay / CO
Switching current 3 A
Switching voltage 6... 250 V AC / 6...60 V DC
Switching threshold via potentiometer
Voltage window        small 10 % AC / 20 % DC // large 12 % AC / 25 % DC adjustable
Hysteresis 5 % AC / 6 % DC of input
Temperature coefficient   < 300 ppm K
Step response time        < 300 ms
Ambient
temperature range 0 °C...+50 °C

Secure isolation                   EN 50178, 2-way isolation up to 6 kV
Test voltage               4 kVeff / 1 min. Input / Output
Rated
voltage                                          600 V AC/DC at overvoltage category III and pollution degree 2
Approvals cULus




Type                                                             WA5 VMR 3ph

 
Short specification

Limit-value monitoring component   for 1- /3- phase AC and DC voltages
with relay output and electrical isolation
limit-value monitoring component in 22.5 mm width for recording 1-phase
AC/DC voltages 200...400 V or 3-phase AC- voltages of 80...250 V.
A relay contact (CO) with a switching capacity of 750 VA
is available on the output side.
Input ranges, high/low trip alarm, monitored voltage window and
switching behaviour (for working and quiescent currents) can be configured using DIP switches
Switching threshold can be adjusted with front-side potentiometer
Power is supplied via the measured circuit. The I/O circuits have 6 kV of electrical isolation.

 

Approvals

Approvals
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_319222/-S800/-T1z1mm-S80)  
![](https://mdcop.weidmueller.com/mediadelivery/rendition/900_319228/-S800/-T1z1mm-S80)  
ROHS
Conform  
UL File Number Search
[UL Website](https://database.ul.com/cgi-bin/XYV/cgifind/LISEXT/1FRAME/gfilenbr.html)  
Certificate no. (cULus)
E141197