ACT20C-8AI-MRTU-DC-S
Product image
ACT20C-8AI-MRTU-DC-S
ACT20C-8AI-MRTU-DC-S
ACT20C-8AI-MRTU-DC-S
ACT20C-8AI-MRTU-DC-S
ACT20C-8AI-MRTU-DC-S
Dimensioned drawing
ACT20C-8AI-MRTU-DC-S
ACT20C-8AI-MRTU-DC-S

ACT20C-8AI-MRTU-DC-S

Serial interface converter, Input : 8 x 0...10 V DC, Output : 1 x Modbus RTU, Voltage supply: 24 V DC ± 10 %

Produkt ID 8000110028
Product not yet available, preliminary product data.
Download datablad Engineering Support Product Downloads
Anvendte produkter 1
General ordering data Dimensions and weights Temperatures Probability of failure Environmental Product Compliance Input Interface 1 General data Insulation coordination Connection data Classifications

General ordering data

Version
Serial interface converter, Input : 8 x 0...10 V DC, Output : 1 x Modbus RTU, Voltage supply: 24 V DC ± 10 %  
Order No.
8000110028  
Type
ACT20C-8AI-MRTU-DC-S  
GTIN (EAN)
4099986000223  
Qty.
1  Styk

Dimensions and weights

Depth
113,6  mm
Depth (inches)
4,472  inch
Height
119,2  mm
Height (inches)
4,693  inch
Width
22,5  mm
Width (inches)
0,886  inch
Net weight
225  g

Temperatures

Storage temperature
-40 °C...85 °C  
Operating temperature
-40 °C...60 °C  
Humidity
10…90 %, no condensation  

Probability of failure

SIL in compliance with IEC 61508
None  

Environmental Product Compliance

RoHS Compliance Status
Compliant with exemption  
RoHS Exemption (if applicable/known)
7a, 7cI  
REACH SVHC
Lead 7439-92-1  
SCIP
2f6dd957-421a-46db-a0c2-cf1609156924  

Input

Input resistance, voltage
1 MΩ  
Input signal
Voltage source  
Input voltage
0...10 V DC  
Input voltage
30 V max.  
Resolution
±1.2 mV  
Response time
<50 ms  

Interface 1

Baud rate
9600  
14400  
19200  
38400  
57600  
115200 bps  
Bit delay
≤ 3 µs  
Connection type
Screw connection  
Interface
RS485  
Number of devices on the bus, max.
128  
Parity
none  
even  
Protocol
Modbus RTU  
Serial data transfer  
Transmission rate
configurable  

General data

Accuracy
<0.1 % of end value  
Applications
Monitoring of H2 fuel and battery cells  
Configuration
DIP switch  
Galvanic isolation
between input ⁄ output ⁄ supply  
Installation advice
Indoors only  
Nominal power consumption
1,5  VA
Operating altitude
≤ 2000 m  
Protection degree
IP20  
Rail
TS 35  
Repeat accuracy
± 0.05 %  
Temperature coefficient
<0.02 % / °C  
Voltage supply
24 V DC ± 10 %  

Insulation coordination

EMC standards
EN 61326-1  
Galvanic isolation
between input ⁄ output ⁄ supply  
Impulse withstand voltage
8 kV  
Insulation voltage input or output/supply
5 kVrms / 1 min.  
Pollution severity
2  
Rated voltage
1500 V DC  
Surge voltage category
II  

Connection data

Tightening torque, min.
0,2  Nm
Tightening torque, max.
0,5  Nm
Clamping range, rated connection
2,5  mm²
Clamping range, min.
0,5  mm²
Clamping range, max.
2,5  mm²

Classifications

ETIM 6.0
EC000310  
ETIM 7.0
EC000310  
ETIM 8.0
EC000310  
ETIM 9.0
EC000310  
ETIM 10.0
EC000310  
ECLASS 9.0
19-17-92-90  
ECLASS 9.1
27-21-01-90  
ECLASS 10.0
19-17-92-90  
ECLASS 11.0
19-17-90-90  
ECLASS 12.0
27-06-03-20  
ECLASS 13.0
27-06-03-20  
ECLASS 14.0
27-06-03-20  
ECLASS 15.0
27-06-03-20