text.skipToContent text.skipToNavigation

Download datablad Anvendte produkter

PVN DC 2I 1O 2MPP RD CG 11

Photovoltaics, Combiner Box, Fireman's switch, 2 MPP's, 2 Inputs / 1 Output per MPP, Remote disconnector, Cable gland, 1100 V

Produkt ID 2778870000

Egenskaber

General ordering data

Version	Photovoltaics, Combiner Box, Fireman's switch, 2 MPP's, 2 Inputs / 1 Output per MPP, Remote disconnector, Cable gland, 1100 V
Order No.	2778870000
Type	PVN DC 2I 1O 2MPP RD CG 11
GTIN (EAN)	4064675047629
Qty.	1 Styk

Dimensions and weights

Depth	132 mm
Depth (inches)	5,197 inch
Height	346 mm
Height (inches)	13,622 inch
Width	200 mm
Width (inches)	7,874 inch
Net weight	2.586 g

Temperatures

Ambient temperature	-20 °C...+50 °C
Humidity	5...95 %, no condensation

Environmental Product Compliance

RoHS Compliance Status	Compliant with exemption
RoHS Exemption (if applicable/known)	7a, 7cI
REACH SVHC	Lead 7439-92-1
SCIP	bdab5698-6a20-4370-8e28-8810d882d01a

Guarantee

Time interval

5 years

Electrical characteristics

Current per Maximum Power Point, max.	50 A
Rated DC voltage	1.100 V
Rated short-term current resistance	Rated current: 55 A

Enclosure

Connection type string	Internal terminal (with cable gland feed-through)
Enclosure attachment	Via mounting foots
Impact resistance	IK08 in accordance with IEC 62208 IK10 in accordance with IEC 62262
Insulating material	Polyester glass-fibre reinforced, Polycarbonate
Protection class	II
Type of mounting	Wall mounting 4 screws

General data

Installation location	Protected outdoor area (>1 km from sea)
Protection degree	IP65

Inputs

Amount of maximum power points (MPP)	2
DC Input + & -	Wire connection: Type of connection: PUSH IN Compatible cable crossection: EN 50618:2015 Wire cross-section, min.: 2,5 mm² Wire cross-section, max.: 16 mm²
Fuse type	Neither fuse cartridge nor holder
Max. number of DC inputs	per Maximum Power Point 2 inputs connected in parallel
Number of conduit inlets	4
Number of string inputs per MPP	≤ 2
Number of inputs	4

Outputs

DC Output + & -	Wire connection: Type of connection: PUSH IN Compatible cable crossection: TÜV 2 Pfg1169/08.07 Wire cross-section, min.: 2,5 mm² Wire cross-section, max.: 16 mm²
Max. number of DC outputs	per Maximum Power Point 1 output

Remote disconnector

Automatic reclosing after voltage drop	Yes
Number of operating cycles	10000
Control voltage	100 V AC - 250 V AC 50/60Hz
Remote disconnector auxiliary contact	Cable entry: Number of cable entries: 1 Wire connection: Type of connection: Screw terminal connectors Flexible, max. H05(07) V-K: 1,5 mm² w. wire end ferrule, DIN 46228 pt 1, max.: 1,5 mm²
Remote disconnector control contact	Cable entry: Number of cable entries: 1 Wire connection: Type of connection: Screw terminal connectors Flexible, max. H05(07) V-K: 1,5 mm² w. wire end ferrule, DIN 46228 pt 1, max.: 1,5 mm²
Type of power circuit disconnection	Under voltage tripping or manual switch operation
Turn-off time	1.5 s
Current consumption of switch	Type of switch: Fireman switch Current consumption, note: The Peak current only arises for a short time when the capacitors of the fireman switch were previously completely discharged. Current consumption peak: 300 mA Current consumption continuous: 30 mA
Number of breaking operation cycles at rated current	300
Switch disconnector execution	Remote disconnector inside enclosure
Switching disconnector capacity	IEC 60947-3 DC-PV1

Important note

Product information

Intended use of the UPS: This UPS has been especially developed as a safety device for direct current (DC) photovoltaic installations. The DC disconnect switch is used to disconnect the connected strings of the installation in case of an emergency situation. Such an emergency situation could be in case of fire.

Normal operation: The UPS will automatically switch to the off position, breaking the DC connection between the solar panels and the inverter, after the AC power to the UPS is interrupted for longer than five seconds. The UPS will automatically switch to the on position, restoring the DC connection between the solar panels and the inverter, once the AC power to the UPS is restored longer than five seconds.

Special Operation: If the temperature inside the UPS enclosure exceeds the 100°C, the UPS will automatically switch to OFF to protect the internal components and create a safe situation. When the installation is checked and the UPS is not affected, the UPS can be switched ON again by removal and re-applying the AC voltage to the UPS. The UPS will also automatically switch to OFF if there is an internal failure. If this occurs please try to reset the UPS by removal and re-applying the AC voltage to the UPS.

Emergency switch not included.The SCIP number was assigned due to a lead content of more than 0.1 % of the net weight.

Safe use instruction according to ECHA:
The identification of the hazardous substance is sufficient to allow safe use of the article throughout its life cycle, including the service life, disassembly and waste/recycling phase

Downloads

Approval/Certificate/Document of Conformity	[PV Next RD Declaration of Conformity](https://mdcop.weidmueller.com/mediadelivery/asset/900_301043)
Engineering Data	[CAD data -- STEP](https://mdcop.weidmueller.com/mediadelivery/asset/900_251071)
Eplan Data Portal	[Eplan data](https://dataportal.eplan.com/part-details/WEI.2778870000)
CADENAS eCATALOG	[CAX data](https://weidmueller-embedded.partcommunity.com?catalog=weidmueller_qs&part=2778870000)
WSCAD Universe	[WSCAD data](https://wscaduniverse.com/part-detail?manufacturerId=88&type=0&partNumber=2778870000&norm=0)
Technical Documentation	[PVN1M2I4S1FXVXO0TXPX11](https://mdcop.weidmueller.com/mediadelivery/asset/900_245982) [CAD data -- Schematic diagram](https://mdcop.weidmueller.com/mediadelivery/asset/900_290533)
User Documentation	[MANUAL PV NEXT RD DE/EN](https://mdcop.weidmueller.com/mediadelivery/asset/900_262445)
White paper	[Fact Sheet DE PV CB Lastentrennschalter](https://mdcop.weidmueller.com/mediadelivery/asset/900_290540) [Fact-Sheet EN PV CB Load break switch](https://mdcop.weidmueller.com/mediadelivery/asset/900_290549) [Fact Sheet DE PV Feuerwehrschalter](https://mdcop.weidmueller.com/mediadelivery/asset/900_310692) [Fact Sheet EN PV Fireman switch](https://mdcop.weidmueller.com/mediadelivery/asset/900_310693)
Catalogues	[Catalogues in PDF-format](LINK/Catalog.html)

Classifications

ETIM 6.0	EC002928
ETIM 7.0	EC002928
ETIM 8.0	EC003857
ETIM 9.0	EC003857
ECLASS 9.0	22-57-92-03
ECLASS 9.1	22-57-02-90
ECLASS 10.0	22-57-02-90
ECLASS 11.0	22-57-02-92
ECLASS 12.0	22-57-02-92
ECLASS 13.0	22-57-02-92
ECLASS 14.0	22-57-02-92

Tender specification sheets

Long specification

Automatic ON and OFF switching fireman switch for the connection to 2 MPP tracker in the inverter.
Suitable for remote disconnection of the DC side by the fire department.
Max. string voltage Uoc: 1100V

MPP1:
2 inputs, connection via M25 cable gland with 3x7mm Ø cable entry. PUSH IN connection / 2.5 - 6mm² single-wire, multi-wire, with/without ferrule.
1 output, connection via M25 cable gland with 3x7mm Ø cable entry. PUSH IN connection / 2.5 - 6mm² single-wire, multi-wire, with/without ferrule.

MPP2:
identical to MPP1

DC fireman switch:
Switching off by undervoltage tripping.
Automatic reconnection after the control voltage (230 V AC) is applied again.
With signal contact.

Connection of the fireman switch control line 230 VAC via cable glands (8-12mmØ) max. conductor cross-section: 1.5mm².
Connection of the signal contact 24 VDC via cable glands (8-12mmØ) max. conductor cross-section: 1.5mm².
Protection class: IP65.
All built into a glas fibre reinforced polyester housing. Dimensions HxWxD: 364x200x132mm.

Approval according to low voltage switchgear IEC 61439-1:2011 and EN 61439-2:2011

Approvals