ACT20M-FRQ-AO-S
Product image
ACT20M-FRQ-AO-S
Connection diagram
ACT20M-FRQ-AO-S
Dimensional drawing
ACT20M-FRQ-AO-S

ACT20M-FRQ-AO-S

Frequency signal converter, including rail bus supply, Input : Frequency, Output : 0(4)-20 mA, 0(2)-10 V

Tuotteen tunnus 2825020000
Avaa konfiguraattorissa
Lataa tietosivu Engineering Support Product Downloads
Lisävarusteet 5 Samankaltaiset tuotteet 2
Tanúsítványok General ordering data Dimensions and weights Temperatures Environmental Product Compliance Input Output General data Insulation coordination Connection data EMC conformity and approvals Part description Classifications

Tanúsítványok

ROHS
Megfelel 

General ordering data

Version
Frequency signal converter, including rail bus supply, Input : Frequency, Output : 0(4)-20 mA, 0(2)-10 V 
Order No.
2825020000 
Type
ACT20M-FRQ-AO-S 
GTIN (EAN)
4064675360834 
CPZ
1 Pezzo

Dimensions and weights

Depth
114,3 mm
Depth (inches)
4,5 inch
Height
112,5 mm
Höhe (inch)
4,429 inch
Width
6,1 mm
Szélesség (coll)
0,24 inch
Net weight
80 g

Temperatures

Storage temperature
-40 °C...85 °C 
Operating temperature
-25 °C...70 °C 
Humidity
0...95 % (no condensation) 

Environmental Product Compliance

RoHS Compliance Status
Compliant with exemption 
RoHS Exemption (if applicable/known)
7a, 7cI 
REACH SVHC
Lead 7439-92-1 
SCIP
2f6dd957-421a-46db-a0c2-cf1609156924 

Input

Input frequency
adjustable 
0…100kHz 
Number inputs
1 
Sensor
NAMUR sensor, according to EN60947-5-6 
NPN / PNP transistor (trig-level low: ≤4 V high: ≥7 V ) 
TTL (trig-level low: ≤0.8 V high: ≥2.0 V) 
Tacho (trig-level low: ≤-50 mV high: ≥+50 mV) 
Special current (trig-level: user-defined) 
Special voltage (trig-level: user-defined) 
S0 (trig-level low: ≤2.2 mA high: ≥9.0 mA ) 
Sensor supply
5…17 V 

Output

Load impedance current
≤ 600 Ω 
load impedance voltage
≥ 10 kΩ 
Number of outputs
1 
Output behaviour on failure downscale
3,5 mA
Output behaviour on failure upscale
23 mA
Output current
0...20 mA 
4...20 mA 
in case of sensor error 
downscale (3,5 mA) 
upscale (23 mA) 
Output signal limit
<28 mA 
Output voltage, note
0(2)...10 V 
0(1)...5 V 
0(0,2)…1 V 
Type
active 
connected control must be passive 

General data

Accuracy
Basic accuracy: 0.0002 Hz 
Configuration
DIP switch or via FDT/DTM software 
Mounting rail
TS 35 
Nominal power consumption
0,5 VA
Operating altitude
≤ 2000 m 
Power consumption, max.
1,2 W
Power consumption, typ.
0,65 W
Protection degree
IP20 
Step response time
≤ 30 ms 
(0…90% / 100…10% of input level) 
Supply voltage
24 V DC ±30 % at terminal or via CH20M rail bus 
Temperature coefficient
≤0,01% of measurement range⁄°C 

Insulation coordination

EMC standards
IEC 61326-1 
Galvanic isolation
3-way isolator 
Insulation voltage
2.5 kVeff /1 min. 
Pollution severity
2 
Rated voltage
250 V 
300 V 
Surge voltage category
II 

Connection data

Type of connection
Screw connection 
Tightening torque, min.
0,4 Nm
Meghúzási nyomaték, max.
0,6 Nm
클램프 범위, 정격 결선
2,5 mm²
Zakres zaciskania, min.
0,5 mm²
Zakres zaciskania, maks.
2,5 mm²
Поперечное сечение подключаемого провода AWG, мин.
AWG 30 
Поперечное сечение подключаемого провода AWG, макс.
AWG 14 

EMC conformity and approvals

EMC standards
IEC 61326-1 
Standards
IEC 61010-1 

Part description

Product description
The universal frequency measuring transducer, which can be configured via software, disconnects and converts input signals (frequency, Namur, NPN, PNP, speedometer, TTL and S0) into an active analogue standard output signal. The power supply is galvanically isolated from the input and output (3-way isolation) by means of direct wiring. The model ACT20M-FRQ-AO-S can be supplied via the Weidmüller DIN rail bus 

Classifications

ETIM 8.0
EC002918 
ETIM 9.0
EC002918 
ETIM 10.0
EC002918 
ECLASS 14.0
27-21-01-28 
ECLASS 15.0
27-21-01-28