VPU I 3+1 R 280V/12,5KA

Surge voltage arrester, Low voltage, with remote contact, TN-C-S, TN-S

Product ID 1352240000

Eigenschappen

General ordering data

Version	Surge voltage arrester, Low voltage, with remote contact, TN-C-S, TN-S
Order No.	1352240000
Type	VPU I 3+1 R 280V/12,5KA
GTIN (EAN)	4050118158021
Qty.	1 items

Dimensions and weights

Depth	69 mm
Depth (inches)	2,717 inch
Height	106 mm
Height (inches)	4,173 inch
Width	71,2 mm
Width (inches)	2,803 inch
Mounting dimension - height	75 mm
Net weight	623 g

Temperatures

Storage temperature	-40 °C...80 °C
Operating temperature	-40 °C...70 °C
Humidity	5 - 95% rel. humidity

Environmental Product Compliance

RoHS Compliance Status	Compliant without exemption
REACH SVHC	No SVHC above 0.1 wt%

Connection data, remote alert

Connection type	PUSH IN
Cross-section for connected wire, solid core, max.	1,5 mm²
Cross-section for connected wire, solid core, min.	0,14 mm²
Stripping length	8 mm

General data

Colour	black orange blue
Design	Installation housing; 4TE Insta IP 20
Optical function display	green = OK; red = arrester is defective - replace
Protection degree	IP20
Rail	TS 35
Segment	Power distribution
UL 94 flammability rating	V-0
Version	with remote contact

Insulation coordination acc. to EN 50178

Pollution severity	2
Surge voltage category	IV

Rated data IEC / EN

Discharge current I_max (8/20µs) N-PE	100 kA
Discharge current I_max (8/20µs) wire-PE	50 kA
Discharge current I_n (8/20µs) N-PE	50 kA
Discharge current I_n (8/20µs) wire-PE	20 kA
Energy coordination (≤10 m)	Type I Type II Type III
Follow-on current extinguishing capability I_fi	Not available due for technical reasons
Fuse	250 A gL (if back up fuse > 250 A)
Leakage current at U_n	100 µA
Lightning test current I_imp(10/350 µs) (L-PE)	12,5 kA
Lightning test current, I_imp (10/350 µs) (N-PE)	50 kA
Low voltage network	TN-C-S TN-S
Mains voltage	230 V / 400 V
Max. continuous voltage, Uc (AC)	280 V
Max. continuous voltage, Uc (N-PE)	260 V
Number of poles	4
Protection level U_p at I_N (L/N-PE)	≤ 1.4 kV
Protection level U_p at I_N (N-PE)	≤ 1.5 kV
Rated voltage (AC)	230 V
Requirements category acc. to IEC 61643-11	Type I Type II
Requirements class, acc. to EN 61643-11	T1 T2
Response time	≤ 25 ns ≤ 100 ns
Short-circuit current rating I_SCCR	25 kA
Signalling contact	250 V 1A 1CO
Standards	IEC61643-11, EN61643-11
Temporary surge voltage (over-voltage) - TOV	438 V
Voltage type	AC

Connection data

Stripping length	15 mm
Type of connection	Screw connection
Stripping length, rated connection	15 mm
Tightening torque, min.	2 Nm
Tightening torque, max.	3 Nm
Clamping range, rated connection	16 mm²
Clamping range, min.	4 mm²
Clamping range, max.	35 mm²
Wire cross-section, solid, min.	2,5 mm²
Wire cross-section, solid, max.	16 mm²
Wire connection cross section, finely stranded, min.	2,5 mm²
Wire connection cross section, finely stranded, max.	25 mm²
Conductor cross-section, flexible, AEH (DIN 46228-1), min.	2,5 mm²
Conductor cross-section, flexible, AEH (DIN 46228-1), max.	50 mm²
Connection cross-section, stranded, min.	2,5 mm²
Connection cross-section, stranded, max.	50 mm²

Electrical data

Voltage type

General data

Number of poles	4
Protection degree	IP20
Colour	black orange blue

Important note

Product information

Only applicable to IT power systems where the earth on the distribution transformer is interconnected with the earth on the consumer side (RE=RA in Figure 44.A1 of IEC 60634-4-44:2018).

Downloads

Approval/Certificate/Document of Conformity	[EU_Konformitätserklärung / EU_Declaration_of_Conformity](https://mdcop.weidmueller.com/mediadelivery/asset/900_86294)
Engineering Data	[CAD data -- STEP](https://mdcop.weidmueller.com/mediadelivery/asset/900_61351)
Eplan Data Portal	[Eplan data](https://dataportal.eplan.com/part-details/WEI.1352240000)
CADENAS eCATALOG	[CAX data](https://weidmueller-embedded.partcommunity.com?catalog=weidmueller_qs&part=1352240000)
User Documentation	[Beipackzettel / Instruction sheet](https://mdcop.weidmueller.com/mediadelivery/asset/900_35385)
Catalogues	[Catalogues in PDF-format](LINK/Catalog.html)

Classifications

ETIM 6.0	EC000941
ETIM 7.0	EC000941
ETIM 8.0	EC000941
ETIM 9.0	EC000941
ECLASS 9.0	27-13-08-05
ECLASS 9.1	27-13-08-05
ECLASS 10.0	27-13-08-05
ECLASS 11.0	27-13-08-05
ECLASS 12.0	27-17-90-90
ECLASS 13.0	27-17-90-90
ECLASS 14.0	27-17-90-90

Tender specification sheets

Long specification

Multi-pin lightning arrestor according to the requirements of Class I in accordance with IEC 61643-11, EN61643-11:2013. On interface transition from 0 to 1 (in accordance with 1312-1), the arrestor, consisting of V0 material, serves as lightning protection providing equipotential bonding and is used in applications in accordance with IEC 61643-12. The use of a non-blow-out sparkover gap, in combination with a high-power varistor, satisfies the inspection requirements for Class I surge protection systems in accordance with the VDEW (Association of German Power Stations) directive. The arrestor is installed in the vicinity of the power supply for the equipment that needs protection, in a standard installation/electrical distribution enclosure. The VPU I 3+1 R 280 V/12.5 kA is used in the TN-C and TN-CS mains network. With thermal separation device on the varistor. If protection is no longer available, the colour in the display window changes from green to red. The functional state is also displayed by a voltage-free signalling contact (changeover). Rated voltage: 230 VAC lightning test current (10/350 µs): 12.5 kA protection level with lightning test current < 1.4 kV 25 kA short-circuit withstand rating with max. back-up fuse of 250 A gl telecommunication output: contact: 250 V/0.5 A 48 VDC/0.1 A, type: Weidmüller VPU I 3+1 R 280 V/12.5 kA, Order No. 1352240000 or equivalent

Short specification

Class I arrester for LPL III/IV with 12.5 kA suitable for 230/400 V TN-CS, TT mains systems. Protection level < 1.4 kV. With remote alert Type: Weidmüller VPU I 3+1 R 280 V/12.5 kA Order no. 1352240000 or equivalent

Approvals