ACT20M-CI-CO-ILP-S

Passive isolator, Input current loop feed, 1-channel, Input : 0(4)-20 mA, Output : 0(4)-20 mA

Produkt ID 1176070000

General ordering data

Version	Passive isolator, Input current loop feed, 1-channel, Input : 0(4)-20 mA, Output : 0(4)-20 mA
Order No.	1176070000
Type	ACT20M-CI-CO-ILP-S
GTIN (EAN)	4032248970148
Qty.	1 Styk

Dimensions and weights

Depth	114,3 mm
Depth (inches)	4,5 inch
Height	112,5 mm
Height (inches)	4,429 inch
Width	6,1 mm
Width (inches)	0,24 inch
Net weight	80 g

Temperatures

Storage temperature	-40 °C...85 °C
Operating temperature	-25 °C...70 °C
Humidity at operating temperature	0...95 % (no condensation)
Humidity	40 °C / 93 % rel. humidity, no condensation

Probability of failure

SIL in compliance with IEC 61508	None
MTBF	699 a

Environmental Product Compliance

RoHS Compliance Status	Compliant with exemption
RoHS Exemption (if applicable/known)	7a, 7cI
REACH SVHC	Lead 7439-92-1
SCIP	2f6dd957-421a-46db-a0c2-cf1609156924

Input

Input current	0...20 mA 4…20mA
Input voltage	> 3 V @ 20 mA
Number of inputs	1
Sensor	Current source
Voltage drop, current input	1.25 V + 0.015 V_out @25°C

Output

Cut-off frequency (-3 dB)	100 Hz
Load impedance current	≤ 600 Ω @ max 23mA
Number of outputs	1
Output current	0...20 mA 4...20 mA
Type	active connected control must be passive

General data

Accuracy	<0.1 % of measuring range
Configuration	none
Galvanic isolation	2-way isolator
Nominal power consumption	1,2 VA
Operating altitude	≤ 2000 m
Power consumption	30 mW
Protection degree	IP20
Rail	TS 35
Step response time	≤ 5 ms
Temperature coefficient	≤ 0.01 % / °C
Voltage supply	Loop powered, via 4…20 mA input

Insulation coordination

EMC standards	EN 61326-1
Galvanic isolation	2-way isolator
Insulation voltage	2.5 kV_eff /1 min.
Pollution severity	2
Rated voltage	300 V_eff
Surge voltage category	II

Data for Ex applications (ATEX)

Installation location	Device installed in safe area, zone 2
Marking	II 3 G Ex nA IIC T4 Gc

Connection data

Type of connection	Screw connection
Tightening torque, min.	0,4 Nm
Tightening torque, max.	0,6 Nm
Clamping range, rated connection	2,5 mm²
Clamping range, min.	0,5 mm²
Clamping range, max.	2,5 mm²
Wire connection cross section AWG, min.	AWG 30
Wire connection cross section AWG, max.	AWG 14

EMC conformity and approvals

EMC standards	EN 61326-1
Standards	IEC 61010-1

Important note

Product information

The ACT20M-CI-CO-ILP-S passive isolator isolates standard analogue current signals.An analogue input current signal is linearly converted to an analogue output current signal and is galvanically isolated. Power is supplied through the input measuring circuit (input loop-powered).

Downloads

Approval/Certificate/Document of Conformity	DNV-GL certificate FM certificate IECEXx certificate ATEX certificate UL certification for canada Declaration of Conformity
Engineering Data	CAD data -- STEP
Eplan Data Portal	Eplan data
CADENAS eCATALOG	CAX data
User Documentation	Instruction sheet
Catalogues	Catalogues in PDF-format

Classifications

ETIM 6.0	EC002653
ETIM 7.0	EC002653
ETIM 8.0	EC002653
ETIM 9.0	EC002653
ECLASS 9.0	27-21-01-20
ECLASS 9.1	27-21-01-20
ECLASS 10.0	27-21-01-20
ECLASS 11.0	27-21-01-20
ECLASS 12.0	27-21-01-20
ECLASS 13.0	27-21-01-20
ECLASS 14.0	27-21-01-20

Tender specification sheets

Long specification

Standard signal passive isolator
1-channel passive isolator in 6.1 mm width input-loop powered,
for transmitting and isolating analogue DC current signals 0/4...20 mA.

Add-on housing for TS35 rail mounting
Dimensions: L/W/H 114.3/ 6.1/ 112.5 mm
Screw connection / Nominal cross-section 2.5 mm²Protection degree: IP 20

Input                          0/4...20 mA
Output                                              0/4...20 mA
Load resistance             < 600 Ohm
Transmission error               < 0,1 % v. E.
Limit frequency 100 Hz
Auxiliary power                                     0/4...20 mA input current loop
Power loss approx. 0.9 W
Ambient
temperature range -25 °C...+70 °C

Isolation                                EN 61010-1, 2-way isolation up to 2.5 kV AC/DC
Test voltage                               2.5 kV input against output against auxiliary power
Rated
voltage                                          300 V AC/DC at overvoltage category II and pollution degree 2
Approvals cULus, FM Div2, ATEX Zone2, DNV, GL

Type ACT20M-CI-CO-ILP-S

Short specification

Standard signal passive isolator
1-channel signal passive isolator in 6.1 mm width with input current loop feed,
for transmitting and isolating analogue DC current signals from 0/4 to 20 mA

Approvals